|
Product Details:
|
| Charge Voltage: | 24V | Charge Current: | 150A |
|---|---|---|---|
| Over Charge Volt: | 3.75±0.25 | Over Charge Volt Protect Delay: | 1 |
| Over Charge Volt Release: | 3.55±0.05 | Constant Discharge Current: | 150A |
| Peak Discharge Current: | 450±10 | Balance Current: | 35±5 |
| Highlight: | 150A 8S24V bms in battery,150A 8S24V intelligent battery management system,2 cables 8S24V bms in battery |
||
3.2V Lithium Battery 8S24V 150A common separate port UART
This BMS is for 8 lithium batteries in series,24V.
80A-500A for your option.
We have common port and separate port.There are 2 cables for Common port,3 cables for separate common port.
If you don't have eclectrician knowleage,pls follow the guide as below
1, PIs do not insert balance wires into BMS before connecting batteries, must make sure connecting with batteries correct.
2, The sequence of connecting wires for BMS:
Notes: PIs ensure to use balancing wires from Daly!
1. From thin black balance wire to start, the 2nd wire(thin red wire) connect with the 1st battery's positive pole. Then connect each ell's positive pole in order until the last one B+;
After finished wiring:
Measure whether the B + and B-voltage and B + and P-voltage of the battery are equal, If yes, it means the BMS works normally and can be used. If not, please recheck according to the above wiring sequence.
BMS 8S 24V 150A Common port Separate port Specification
| Content | Spec | Unit | ||||||
| 80A | 100A | 120A | 150A | 200A | 250A | |||
| Discharge | constant discharge current | 80 | 100 | 120 | 150 | 200 | 250 | A |
| peak discharge current | 260±30 | 300±30 | 360±50 | 450±10 | 450±10 | 600±100 | A | |
| Over current protection | 260±30 | 300±30 | 360±50 | 450±10 | 450±10 | 600±100 | A | |
| charge | charge voltage | Series No.*3.65 | V | |||||
| charge current | 80 | 100 | 120 | 150 | 200 | 250 | A | |
| Over charge protection | over charge volt | 3.75±0.025 | V | |||||
| over charge volt protect delay | 1 | S | ||||||
| Over charge volt release | 3.55±0.05 | V | ||||||
| Power balancing | Power balance volt | 3.5 | V | |||||
| balance release volt | 3.5 | V | ||||||
| balance current | 35±5 | mA | ||||||
| Over discharge protection | Over discharge detect volt | 2.2±0.1 | V | |||||
| Over discharge detect delay | 1 | S | ||||||
| Over discharge volt release | 2.7±0.05 | V | ||||||
| Over current protection | Over current detect delay | 1 | MS | |||||
| Over current protect release | Off-load | |||||||
| Short circuit protection | Short circuit protection | External load short circuit | ||||||
| Short circuit detect delay | 250 | uS | ||||||
| Short circuit detect release | Off-load | |||||||
| Temperature protection | Temp protection | none | ℃ | |||||
| resistance | Main circuit resistor | ≤20 | mΩ | |||||
| Self-consumption | Working current | 100 | uA | |||||
| Sleepy current(when battery is over discharged ) | ≤20 | uA | ||||||
| Working temp | temp range | -40~80 | ℃ |
|||||
Smart BMS function:You can set up the parameter settings,SOC,current,discharge type,charging temp,voltage,sleep,resistance on your phone.
Where to buy battery management system?
Deligreen!!
Pls go to the bottom of this page,and send us your requirement,we will contact you by email or whatsapp to recommend the BMS you need.We can ship to you freight charge included.
How does battery management system work?
The battery management system monitors battery conditions and takes actions to extend battery life. If excessive battery drain is detected, the system temporarily disables some electrical systems to protect the battery.
How to choose the BMS that I need?
You need to make sure of following
1. battery type:lifepo4,lto,NCM battery.The different battery with different voltage and capacity,3.2V lifepo4,3.7V NCM,2.3V lto
2. charge current:Range 5A-250A
3. discharge current:Range 10A-500A
4. battery pack(series,parallel):3S-32S,customized optional
5. Peak discharge current:The highest discharge can a BMS stand
Where does the BMS use?
If you have batteries used in these applications,you must use a BMS.
What smart/soft function does it have?
There are severl options for the smart BMS,which you can have different function from it.Deligreen's smart BMS has CAN/UART/FAN,and LCD control.It denpends on what protocal of your battery is.We will supply the relevant cables for the connection,UART,USB.CAN.
Every smart BMS has a bluetooth module along with the shippment,as well the USB-UART cable.
The other parts to be given according to the type you place.
FAQ:
Q:Which current of the PCB should i choose?
A:Take 13S 48V pack as an example: Which PCB you should choose depends on the power of your motor or the current limitation of your controller. Below 350W ,you can choose 16A.Below 500W, you can choose 18A, Below 800W, you can choose 35A,Below 1KW, you can choose 60A. Above 1200W, the same. If you are not sure, please contact us freely.
Q:What battery types do your BMS work with?
A:Our BMS can work for lithium phospate battery(Lifepo4)and NCM battery,lithium ion battery,ple let us know what your battery type before placing order.
Q:What BMS range can you supply?
A:Deligreen is a professional BMS supllier with abundant BMS range.Series from 3S-32S,Current from 10A-500A,if you need more series,pls contact us.
Q:Can I watch the battery status from my mobile phone?
A:Yes,this is waht a samrt BMS do,you can watch the status of your batteries in your APP throush bluetooth connected between phone and the BMS.
About US
Changsha Deligreen Power Co.LTD,founded in 2010,is a "Green Energy Solution Service Provider".
Newest technology,new idea,hard-working and honest people.
Focus on lithium rechargeable battery,BMS,Balancer,charger and relative products.
BMS is one of best sellers,we've been receiving thousands of good comment from our clients because of its good quality and function
If you have anything dissatisfied.Please email the manager:info@deligreenpower.com
Contact Person: Leo Zeng
