|
Product Details:
|
| Charge Voltage: | 24V | Charge Current: | 40A |
|---|---|---|---|
| Over Charge Volt: | 3.75±0.25 | Over Charge Volt Protect Delay: | 1 |
| Over Charge Volt Release: | 3.55±0.05 | Constant Discharge Current: | 80A |
| Peak Discharge Current: | 260±30 | Balance Current: | 35±5 |
| High Light: | UART USB bms for lithium ion battery,UL 8S24V80A bms for lithium ion battery,UART 8S24V80A lifepo4 battery management system |
||
Smart Battery Management System Common Port UART USB 8S24V80A
Why do we need battery management system?
Battery Management Systems are the brains/CPU behind battery packs. They manage the output, charging,discharging and provide notifications on the status of thebattery pack. They also protect the batteries from damage.
Lithium ion is a kind of active metal,compared to lead acid battery,lithium ion is more active,which casuses over charge,over discharge problem.It needs a protection.BMS is the one that protect your battery from be damaged.
Now you are replacing the lead acid battery with lithium battery,it's worthy spending little money on protection of your batteries,which can save much money.
What is battery management system BMS?
Deligreen BMS is defined as an electronic system that manages a rechargeable battery(lithium phosphate,NCM battery,single cell or battery pack) by monitoring its state, calculating secondary data, reporting that data, protecting the battery, controlling its environment, and/or balancing it.This is a very worthy of money to make your battery packs a BMS.
Why deligreen BMS?
Deligreen was founded in 2010 and we have sold BMS for more than 10 years.BMS is one of our best sellers.The customers from more than 90 countries in the world have been using Deligreen's BMS,our BMSes are protecting tremendous amount of batteries in the world.It's worthy the every dollar/cent you spend on our BMS.;)
Where to buy battery management system?
Deligreen!!
Pls go to the bottom of this page,and send us your requirement,we will contact you by email or whatsapp to recommend the BMS you need.We can ship to you freight charge included.
How does battery management system work?
The battery management system monitors battery conditions and takes actions to extend battery life. If excessive battery drain is detected, the system temporarily disables some electrical systems to protect the battery.
How to choose the BMS that I need?
You need to make sure of following
1. battery type:lifepo4,lto,NCM battery.The different battery with different voltage and capacity,3.2V lifepo4,3.7V NCM,2.3V lto
2. charge current:Range 5A-250A
3. discharge current:Range 10A-500A
4. battery pack(series,parallel):3S-32S,customized optional
5. Peak discharge current:The highest discharge can a BMS stand
What smart/soft function does it have?
There are severl options for the smart BMS,which you can have different function from it.Deligreen's smart BMS has CAN/UART/FAN,and LCD control.It denpends on what protocal of your battery is.We will supply the relevant cables for the connection,UART,USB.CAN.
Every smart BMS has a bluetooth module along with the shippment,as well the USB-UART cable.
The other parts to be given according to the type you place.
Where to the BMS use?
BMS bluetooth common separate parameter
| Content | Spec | Unit | ||||||
| 80A | 100A | 120A | 150A | 200A | 250A | |||
| Discharge | constant discharge current | 80 | 100 | 120 | 150 | 200 | 250 | A |
| peak discharge current | 260±30 | 300±30 | 360±50 | 450±10 | 450±10 | 600±100 | A | |
| Over current protection | 260±30 | 300±30 | 360±50 | 450±10 | 450±10 | 600±100 | A | |
| charge | charge voltage | Series No.*3.65 | V | |||||
| charge current | 80 | 100 | 120 | 150 | 200 | 250 | A | |
| Over charge protection | over charge volt | 3.75±0.025 | V | |||||
| over charge volt protect delay | 1 | S | ||||||
| Over charge volt release | 3.55±0.05 | V | ||||||
| Power balancing | Power balance volt | 3.5 | V | |||||
| balance release volt | 3.5 | V | ||||||
| balance current | 35±5 | mA | ||||||
| Over discharge protection | Over discharge detect volt | 2.2±0.1 | V | |||||
| Over discharge detect delay | 1 | S | ||||||
| Over discharge volt release | 2.7±0.05 | V | ||||||
| Over current protection | Over current detect delay | 1 | MS | |||||
| Over current protect release | Off-load | |||||||
| Short circuit protection | Short circuit protection | External load short circuit | ||||||
| Short circuit detect delay | 250 | uS | ||||||
| Short circuit detect release | Off-load | |||||||
| Temperature protection | Temp protection | none | ℃ | |||||
| resistance | Main circuit resistor | ≤20 | mΩ | |||||
| Self-consumption | Working current | 100 | uA | |||||
| Sleepy current(when battery is over discharged ) | ≤20 | uA | ||||||
| Working temp | temp range | -40~80 | ℃ | |||||
3 Steps to test the BMS
1. Make sure to use the attached detective wires of our bms.
The blck wire is for the total negative pole.
2. Connect the wire to the battery pack,measure the voltage through the wire,it should be equal with the voltage of each cell.
If the votage is different,it means wrong wiring.
3. Make sure the voltage is same,plug the bms in.Make the multimeter point to Ω,measure the resistance value between P- and B after short connect the probes of multimeter.
If the value is 0,the BMS is good.
BMS instruction manual
First Preparation before installation
Make sure the batteries are of good consistency.The volt difference is no more than 0.05V,inner resistance is no more than 5mΩ,capacity difference lower than 30mAh. Connect the batteries in parallel first and then in series.the better performance of batteries consistency is, the higher performance of the BMS.
Second, wiring instructions
Attention: please use our wires for our BMS.Don’t use other factories’ wires which can’t match with our BMS.
Step 1 B-(blue thick wire): Connect to battery pack total negative pole -
Step 2, Disconnect the wires for batteries from the BMS side.
Step 3,Connect the wires to batteries. Start from the thick black wire to total negative pole(B1-),then connect the 2nd red thin wire to the 1st battery positive pole(B1+)
B2+,B3+B4+......till the last red thick wire.
Step 4,Finishing all the wires to each batteries,don’t plug into the BMS directly. We suggest you use multimeter measure the voltage of two adjacent metal terminals(You can see the white connector with silver metal pins on the BMS).if the voltage is 3.0~4.2V(LiNCM),2.0~3.6V(LiFepo4), 1.5~2.75V(LTO),which means the wiring is correct.
Step 5,Ensure the wires are connected to batteries correctly, all voltage is normal, you can plug the wires into the BMS.
Step 6 P-: Connect P-(black thick wire) to load - and charger -
(if you ordered “common port”)
Charger+ connect to C-(yellow wire) load+ connect to P-(Black thick wire)
(if you ordered “separate port”)
Step 7 charger+ and load+ connect to battery +,please use thick wire
Third,Measure the total volt of the pack, and the output voltage of the BMS.if the voltage is the same,it means the wiring is correct.You can use the BMS now. Otherwise please check the wiring again according to the tips above.
FAQ:
Q:Which current of the PCB should i choose?
A:Take 13S 48V pack as an example: Which PCB you should choose depends on the power of your motor or the current limitation of your controller. Below 350W ,you can choose 16A.Below 500W, you can choose 18A, Below 800W, you can choose 35A,Below 1KW, you can choose 60A. Above 1200W, the same. If you are not sure, please contact us freely.
Q:What battery types do your BMS work with?
A:Our BMS can work for lithium phospate battery(Lifepo4)and NCM battery,lithium ion battery,ple let us know what your battery type before placing order.
Q:What BMS range can you supply?
A:Deligreen is a professional BMS supllier with abundant BMS range.Series from 3S-32S,Current from 10A-500A,if you need more series,pls contact us.
Q:Can I watch the battery status from my mobile phone?
A:Yes,this is waht a samrt BMS do,you can watch the status of your batteries in your APP throush bluetooth connected between phone and the BMS.
About US
Changsha Deligreen Power Co.LTD,founded in 2010,is a "Green Energy Solution Service Provider".
Newest technology,new idea,hard-working and honest people.
Focus on lithium rechargeable battery,BMS,Balancer,charger and relative products.
BMS is one of best sellers,we've been receiving thousands of good comment from our clients because of its good quality and function
If you have anything dissatisfied.Please email the manager:info@deligreenpower.com
Contact Person: Leo Zeng
